To Seal Or Not To Seal

Mar 31
20:59

2005

Barry Shultz

Barry Shultz

  • Share this article on Facebook
  • Share this article on Twitter
  • Share this article on Linkedin

I get many emails from people with refilling problems and one of the biggest is cartridges that just won't print after refilling them. There are many reasons for this but one problem in particular has been popping up with frequency lately. People are sealing cartridges that must not be sealed in order for them to work properly, or at all for that matter.

mediaimage

If you are ever in question as to weather to seal the refilling holes on your cartridge here are some tips. If the refilling hole is on the bottom of the cartridge you better seal it because if you don't it will obviously leak inside your printer. In these cases the breather holes on the top of the cartridge have not been disturbed so it should work properly if no other problems exist.

If the cartridge is a Canon BCI-3e or BCI-6 you better seal it and seal it good! For some reason these cartridges must have an air tight seal over any refilling hole or the ink will completely drain out of the ink port that feeds the ink into your printer which causes quite a mess. These seem to defy physics. A dab of hot glue works well for these cartridges and the "dimple" of glue comes off easily with your fingernail when you want to refill again.

Cartridges that should NOT be sealed are all HP color cartridges. In particular is the C6578. This cartridge is deceptive because when you
refill you are instructed to punch the little plugs in that are on the top of the cartridge. While these plugs may look to be completely sealed they are not. A close inspection will reveal that these plugs are actually vented. So people looking to restore the cartridge to its original condition will seal these holes. Bad move,To Seal Or Not To Seal Articles the result is vapor lock and no print.

If you have just refilled a cartridge and are having problems getting it to print properly check to make sure that you didn't cause a vapor lock problem by sealing the breather holes or refilling holes. Exception, of course, to the cartridges profiled above.

Epson cartridges generally work well with the refill holes uncovered if it was refilled from the top. The new design of Epson cartridges is very confusing. These are the new skinny ones like the T04xx and T08xx series of cartridges. The OEM cartridges are comprised of a series of chambers. They are harder to refill than their generic counterparts and some instructions will tell you to drill the top and others will tell you to drill in the bottom. Sealing the top hole is not mandatory while sealing the bottom is a must. Some generic versions of these cartridges are sponge filled and are far simpler to refill. You can drill on the top without complication and you don't have to reseal.

So the bottom line is if you are having printing problems after you refill be sure you have not caused the problem by sealing the cartridge and creating a vapor lock.

Also From This Author

Having Fun With The Printer Support Techs

Having Fun With The Printer Support Techs

Many years ago when I was a copier technician my boss would always tell us to push our companies supplies, paper, toner etc.. Of course they wanted to sell more supplies and make more money but their techniques were very questionable. Just like printers you could go out and purchase generic supplies and some worked better than others naturally. Well the supplies that we sold were also mostly generic, however, they were branded with our companies name and logos. Here's where the sneakiness comes in. When a customer complained about a repair cost estimate we were told to blame it on their inferior generic supplies and to further that the repair would have been much cheaper if they were using our over-priced supplies.
My Printer Died - An Epitaph

My Printer Died - An Epitaph

My printer just died. My Epson C60 that I've had for almost 2 years was my buddy. I loved that printer. It was there for me through thick and thin. Sure it had it's quirks and idiosyncrasies like not printing when my office temperature dropped to 17 degrees because I forgot to turn the thermostat up one bitterly cold morning. I had to open the lid and point a ceramic space heater inside to thaw it out.
When Is Black Not Black?

When Is Black Not Black?

Did you notice how many different black inks there are available? At last count we have forty different black inks listed on our web site. You may be wondering how many shades of black can there be? Well there are actually different shades of black which I will explain in a bit.