Free Articles, Free Web Content, Reprint Articles
Saturday, August 24, 2019
 
Free Articles, Free Web Content, Reprint ArticlesRegisterAll CategoriesTop AuthorsSubmit Article (Article Submission)ContactSubscribe Free Articles, Free Web Content, Reprint Articles
 

Steel Forming Four Different Ways

Forming steel tubes, beams and pipes is not as hard as it looks...with the right equipment.  Here are four ways the construction sector bends the metal beams and pipes that support our buildings.

Even as a child, you were most likely bending metal for fun.  Perhaps you were making pipe-cleaner clowns.  Or you might have found paper clips fascinating.   One thing is for certain, the metal you were bending as a child was not steel beams or tubes, and it never had to be strong enough to hold up a stadium roof or a roller coaster.

As adults, we rely on curved steel beams, pipe, tubes, and angles in everything from a simple park bench to spiral staircases to some parts of modern skyscrapers.  Visit any airport or museum built in the past couple decades and count the number of curved metal structures you find.

Have you ever wondered how they do it?  I mean, how can you bend a steel beam and still keep the strength to support an airport roof?  Well, there are four ways.

Roll Forming Steel

Rolling is the best known way to bend metal, perhaps because it is the least costly.  Rolling uses an appropriate size die that adjusts to the steel tube, angle, pipe, channel, bar or steel beam and revolves at the same peripheral speed, turning in opposite directions. As the metal passes through the roll, the machine applies pressure to bend the tubing or the beam to the desired radius.

Rolling is effective when the material metal, plastic, glass, whatever - must be bent a great deal.  For instance, it can produce bends up to 360 degrees. This method is ideal for producing steel coils, spiral staircases and the like.

There are different kinds of rolling processes.  Hot rolling (above the recrystallization temperature) mostly produces sheet metal.  Most non-ferrous metal structures are rolled cold, but steel is usually rolled hot.

Because rolling requires less set-up work and uses pre-made dies, the cost is less than other ways to bend and form steel, so companies often choose this when it suits their specifications.

Mandrel Metal Bending

Mandrel bending is also fairly well known.  In this process, a metal shaft, or mandrel, is fitted inside the steel tube or pipe. As the mandrel moves, it bends the metal around the appropriate sized die to form the radius.

Mandrel works best when the steel tube or pipe has a heavy wall and/or requires a tight radius because it prevents the material from rippling. Mandrel can only bend steel tubing up to 180 degrees, but it produces a bend that is uniform all the way up and down the pipe or tube.  Obviously, this process is of little use for bending metal beams or sheets, however, it is used in bending exhaust pipes, molten glass and in very tiny cases, jewelry.

Press to Bend Steel

The Press method is the third way to bend metal.  The steel tube, pipe, channel, bar or steel beam is fed through the press, which applies pressure every 6 or 7 inches until the material is bent to specifications

Press is used to bend bigger, heavier beams, pipes, channels, bars or tubes (24 inches or thicker) that do not require a very tight radius.

This is a less common process than rolling or mandrel.  However, it is capable of producing large, load-bearing steel support beams used for schools, roofing,  skyscrapers, gymnasiums, malls and bridges.

Table Forming Steel

Table forming is the fourth process.  The steel tube, pipe, or beam is laid out straight and the ends are pulled around the appropriate sized die to form the radius.

Table forming is used primarily to bend smaller, heavier steel tubes, pipes, channels, bars or steel beams that require a tight radius.

But if all that is too much for youFree Reprint Articles, pick up those pipe cleaners and wow your kids with the colorful pipe-cleaner clowns you can form by bending metal at home.

Source: Free Articles from ArticlesFactory.com

ABOUT THE AUTHOR


David Leonhardt is a freelance writer .  He wrote this article for a steel forming client.  See how they form steel and bend pipes or read about their history of steel rolling pipe.



Health
Business
Finance
Travel
Technology
Home Repair
Computers
Marketing
Autos
Family
Entertainment
Law
Education
Communication
Other
Sports
ECommerce
Home Business
Self Help
Internet
Partners


Page loaded in 0.183 seconds