Free Articles, Free Web Content, Reprint Articles
Sunday, December 9, 2018
 
Free Articles, Free Web Content, Reprint ArticlesRegisterAll CategoriesTop AuthorsSubmit Article (Article Submission)ContactSubscribe Free Articles, Free Web Content, Reprint Articles
 

Industrial Makeup Air Units

Negative Air Pressure in industrial manufacturing facilities can create problems such as: * Exhaust fans losing performance, as the building pressure becomes negative. * Pilot light outages and exha...

Negative Air Pressure in industrial manufacturing facilities can create problems such as:

* Exhaust fans losing performance, as the building pressure becomes negative.

* Pilot light outages and exhaust system failure on natural draft gas equipment.

* Cold air drafts and infiltration of dirt and contamination from outside.

* Difficulty opening or closing exterior doors.

Pressure Blower Co. has re-designed its Make-Up Air Units for larger industrial plants ventilation requirements.

Pressure Blower Co. air-handling units (AHU) can be used effectively for negative pressure control at manufacturing facilities:

Space Pressure Control is used to minimize and control the exchange of air between the building and the outside environment or from one building area to another. This may be accomplished in three ways:

- Constant air supply with variable-speed exhaust;

- Variable air supply with constant-speed exhaust;

- Variable Return-Air.

Constant air supply with variable-speed exhaust is recommended where a hot or contaminated environment must be ventilated while maintaining room pressure. Unit may be interlocked to that it only operates with the exhaust system.

Variable Air Supply with constant-speed exhaust may be preferred where fume exhausters or fume hoods are used to provide critical ventilation of contaminants from a “clean” environment while make-up air is used to maintain a positive pressure to prevent infiltration.

In either case, when the system is enabled, a pressure sensor in the building space monitors room pressure. When a high or low pressure reading is detected, the air supply or exhaust is adjusted to compensate.

When controlling a Variable Air Supply unit (or VAV Unit - Variable Air Volume), two methods are available:

- Damper Control - Unit discharge damper is adjusted using the damper motor.

- VFD (Variable Frequency Drive) – Controller adjusts the speed of the blower motor Discharge Damper adjustment is an older method of controlling discharge air volume. Its main advantage is that it only requires positional control of a small discharge damper motor. The major disadvantage is the wasted Horsepower of the blower motor at lower delivery rates.

In recent years, fan speed control using VFDs has become economical. In this application, a standard energy efficient motor is usually adequate down to 75% of normal motor speeds. For a fan speed down to 25%, a premium efficiency motor is required. Inverter duty motors are not usually necessary since at 25% of normal fan speed, air delivery is minimal.

Variable Frequency Drives are also programmable. They are used to provide soft starts and to ramp motor speed up or down in response to signals from the control system ventilating.com fanblower.com highpressureblower.net industrialblowerfan.com industrialfanblower.net industrialfanblower.com pressureblower.net northernindustrialsupplycompany.com industrialpressureblower.com tenderall.com chicagoblowercanada.com cbblower.com buffaloblower.com buffalofan.com nis-co.com canadianblower.com olegsystems.com canadablower.com abbblower.com acmefan.net industrialblower.net fansandblowers.net americanblower.net barryfan.com cincinnatifan.net canadafans.com barryfan.net greenheck.net pennbarry.net pennfan.net tcffan.com.

Finally, in a generally “clean” environment without a critical need to remove large quantities of contaminants, a simple solution to building pressurization is a Return Air Unit with the return air damper motor controlled by building a pressure sensor. When building pressure increases, more inside air is returned through the unit, relieving the pressure. When building pressure fallsArticle Search, more outside air is supplied to the building in order to “pump up the pressure”. Precise control of building pressure by a single piece of equipment can thus be achieved.

Additional information can be found at the Pressure Blower company web site http://www.pressureblower.net/enquiry.php

Susan Terlecky
Industrial Air Handling Systems Designer
fan@pressureblower.net
Pressure Blower Co.
http://www.pressureblower.net/aboutus.php
http://www.pressureblower.net/root-blowers.html

Article Tags: Building Pressure, Pressure Blower, Discharge Damper, Damper Motor

Source: Free Articles from ArticlesFactory.com

ABOUT THE AUTHOR


Susan Terlecky
Industrial Air Handling Systems Designer
fan@pressureblower.net
Pressure Blower Co.
http://pressureblower.net/aboutus.php
http://pressureblower.net/root-blowers.html



Health
Business
Finance
Travel
Technology
Home Repair
Computers
Marketing
Autos
Family
Entertainment
Law
Education
Communication
Other
Sports
ECommerce
Home Business
Self Help
Internet
Partners


Page loaded in 0.189 seconds