Free Articles, Free Web Content, Reprint Articles
Friday, October 18, 2019
 
Free Articles, Free Web Content, Reprint ArticlesRegisterAll CategoriesTop AuthorsSubmit Article (Article Submission)ContactSubscribe Free Articles, Free Web Content, Reprint Articles
 

So, You Want To Be A Wood Turner, Hey

This article will discuss the different options of toolsand wood lathes. The options depend on couple things. What is your niche and what is your budget? Your choice of wood lathes and turning tools will depend on this.

This article will discuss the different options of tools and wood lathes. The options depend on couple things. What is your niche and what is your budget? Your choice of wood lathes and turning tools will depend on this.

I first started turning wood in High School shop class and in the neighbors shop. I drifted away from wood turning for a time because of military service, college, family and career. My career is Forestry, management, harvest and construction. I was able to acquire lots of different types of wood and store them for later use.

My first lathe was a bench mounted Montgomery Ward wood lathe and the set of tool that came with the lathe. After using this lathe for several years I realized, as most turners do that there are bigger and better turnings to do. All that is required is bigger and better tools.

Over the next few years I started to upgrade my equipment. My new lathe was a Jet 14 X 42. There are higher grade tools and specialty tools. There are tools for spindles, tools for bowls, tools for texturing and equipment for supporting your spindles or larger turnings. Think I currently have over 40 different wood turning tools and continue to look for more. The new tools I am looking for are for very special use. I will properly design and make them myself.

Then there are face plats, chucks with all their various jaws and attachments. There are various spur drives and live centers. All these tools have different applications and if you are like me where you do a Variety of different turnings you will use them all; especially if you are selling your work and clients are making special requests. I recently built a vacuum chuck so I could turn the bottom of my bowls, improves the appearance by about 100%. You can buy the vacuum chuck, all ready setup with vacuum pump and accessories. I purchased all the parts separately and then built the vacuum chuck, I saved about $250.

Currently I am looking into one of the big lathes 20” with the electronic speed control. A friend of mine and I are in the process of design and making a boring bar for hollowing large vessels. When I purchased the chucks for holding the turnings, I purchased them with the larger headstock requirements and then used an insert to attach them to a smaller lathe. The smaller lathes require a 1” X 8TPI and the larger 1 ” X 8 TPI. This is generally correct but there are exceptions. If you have dreams of larger lathe spend some time looking at different lathe brands and their specifications, it can save money in the long run.

The other expense that you will incur is finish and sanding. There are a large verity of finishes and sanding methods and I have spent hundreds of dollars trying different things out; my garbage can is very full. Without getting really deep into this subject I will tell you what works for me.

Sanding; I use power sanding and will sand down to 250 grit and sand the finish to 320 grit. Over sanding can create a surface that the finish will not adhere too, finishing compounds all have a sanding requirement in their instructions.

Having a finish that not only looks good but feels good is critical. I use clear water base grain filler to smooth the surface and then use a clear gloss, rub on rub off oil finish. When the finish is dry turn the bottom off and finish bottom same as the bowl. Final step buff and wax.

To sum it up; Wood Turning, Fishing, Photography, Camping, Boating and most other interests whether they are hobbies or professionsComputer Technology Articles, seems to be a good place to spend all your extra money. The art of wood turning is fascinating. There is on limit to what you can do; you are only limited by your fascinating.

Source: Free Articles from ArticlesFactory.com

ABOUT THE AUTHOR


Steve Nicholson is a retired Forester and is now a dedicated wood turner. His wood turnings are for his family and he also sells his projects in a gift shop and by word of mouth. He also owns and operates a website that sells wood turning tools. Please stop by and browse the tools he also has a very interesting blog.



Health
Business
Finance
Travel
Technology
Home Repair
Computers
Marketing
Autos
Family
Entertainment
Law
Education
Communication
Other
Sports
ECommerce
Home Business
Self Help
Internet
Partners


Page loaded in 0.018 seconds